Valkey® Admin’s Send Command is a box for typing Valkey commands, just as in valkey-cli. It shows each reply, times it, and keeps a history you can reuse.
By the end, you’ll have sent commands, read their replies, and seen how Send Command protects the server from risky ones.
Note: Every command and screen on this page is real, from Valkey Admin 1.3.0 connected to Valkey 9.1 on an Apple silicon Mac with macOS 26.
Prerequisites
- Valkey Admin connected to your Valkey server.
Step 1: Open Send Command
Connect first if you haven’t: How to Connect Valkey Admin to a Valkey Server. Then click Send Command in the sidebar. Replies appear on the left, History on the right, and the command box is at the bottom.
Step 2: Send a Command
Type a command exactly as in valkey-cli and click Send:
SET book:4:title "Salt and Starlight"
OK

The reply shows under Response with the round-trip time: how long the command took from Valkey Admin to the server and back.
Step 3: Read Values Back
Send two more, then read the price:
SET book:4:author "Nadia Quill"
SET book:4:price 9.99
GET book:4:price
9.99
Valkey Admin shows the value without the quotes valkey-cli puts around it.

Step 4: Reuse a Command from History
Each entry in History has its time, its round-trip time and two icons: one copies the command, the other runs it again. The documentation (opens in a new tab) adds that you can search the history and compare the results of two commands.
Step 5: See Which Commands It Blocks
Some commands would change the connection that Valkey Admin shares between its pages, or are too risky to send from here. Send Command blocks them. SELECT is one:
SELECT 1

The documentation lists the blocked commands: SELECT, AUTH, HELLO, RESET, QUIT, SHUTDOWN, DEBUG, FLUSHALL and FLUSHDB. To work in another database, set Database when you add the connection.
Step 6: Confirm a Risky Command, or Use a Safer One
Other commands run only after you confirm. KEYS is one, because it can block a server that holds many keys:
KEYS *

To go ahead, type the command into the box and click Run anyway. Or click Cancel and use SCAN, as the warning suggests:
SCAN 0 MATCH book:4:* COUNT 100
Valkey Admin numbers the parts of the reply: 0 is the cursor, and 0 means the scan is complete. 1.0 to 1.2 are the keys found.

The documentation also asks for confirmation before CONFIG RESETSTAT, CONFIG REWRITE, SLAVEOF, REPLICAOF and CLUSTER RESET.
Clean Up
Delete the three keys:
DEL book:4:title book:4:author book:4:price
3
Common Mistakes
| Mistake | What happens | Do this instead |
|---|---|---|
Using SELECT to switch databases | Send Command blocks it | Set Database in the connection |
Running KEYS * on a server with many keys | It can block the server while it runs | Use SCAN, as in Valkey KEYS vs SCAN |
FAQ
Is Send Command the same as valkey-cli?
It sends the same commands to the same server. It also times each reply, keeps a history and stops a few commands that could disrupt the server.
Conclusion
Send Command runs Valkey commands inside Valkey Admin: type, send, read the reply. It keeps your history and guards the server against a short list of risky commands.
Related
- Valkey Tutorial — Part 3: Valkey Admin for Beginners
- How to Browse and Edit Keys in Valkey Admin
- How to Connect Valkey Admin to a Valkey Server
- Valkey KEYS vs SCAN: Which Should You Use?
Additional Resources
Valkey® is a registered trademark of LF Projects, LLC. Redis® is a registered trademark of Redis Ltd. Any rights therein are reserved to Redis Ltd. Other names mentioned are trademarks of their respective owners. JD Bots isn’t affiliated with the Valkey project, LF Projects or Redis Ltd., and isn’t endorsed, supported or certified by them.
0 comments